IRLP OPERATING
PROCEDURES
COMMON MODES
There are two connection modes for an IRLP connection. Direct one-to-one
or, one-to-many via a Reflector.
Direct connect is just like it sounds where node "A" connects direct with node "B". In this mode the two nodes (repeaters) are interconnected and no other IRLP connections are possible. While "A" and "B" are connected, anyone attempting to connect with either node will be told by a recording that - "The node you are calling is currently connected to callsign"
The most common IRLP connection in use today is via the Denver reflector (Ref 2). A reflector is a Linux Computer that is not connected to any radio but rather sits on lots of bandwidth capable of allowing the multiple linking of repeaters by streaming audio back to all nodes that are connected. At any given time there are usually 6 to 10 repeaters around the world interconnected via the reflector. You can always check who is connected to the reflector by visiting http://status.irlp.net and looking for nodes connected to REF 2.
REFLECTOR USE
With reflector use the first thing we must all remember is to leave a gap
between transmissions. So this is probably a good time to list the three
main rules when connected to a reflector:
1. Pause
2. Pause
3. Pause
Due to the slight increase in delays created by multiple Tone Squelch radios in the links between the repeater and IRLP link radio a slight change in our normal operating procedures is required with IRLP.
By leaving a pause between transmissions it:
· allows users on other nodes a chance to check in.
· allows other nodes time to send touch-tone commands to drop their node.
The most important guideline to remember is leaving a pause after pressing the PTT button as well as between transmissions.
MAKING A DIRECT CONNECTION
First of all listen on your local machine before transmitting and then ask if
the repeater is currently in use. Assuming all is clear, identify your
self and give the node you are calling. Example: "VE3xyz for
the Sydney node" - - then enter the ON code for the node and release
your PTT. Your local repeater should come up with a carrier as it waits
for the connection to be established. This can take a few seconds of
dead-air so don't be concerned. When the connection is confirmed the voice
ID of the destination node will be transmitted back to you as well as your nodes
voice ID to the other repeater.
After hearing the confirming voice ID wait at least 15 seconds before transmitting as
· The repeater may be in use, and your entry may have occurred between transmissions.
· The voice ID of your node is longer than the voice ID of their node, and the connection is not made until the ID is fully played.
· Their computer may be slower, and hence take longer to process the connection than yours.
Press and hold the microphone PTT for a second and then announce your presence and your intention. Are you calling someone specifically or just looking for a QSO with another ham in that city.
If no response is heard, announce your call and your intent to drop the link and then touch tone in the OFF code. Not a good idea to transmit touch-tone commands without first giving your callsign. Not only is this courteous it is a regulatory issue in some countries who may be connected to the reflector.
Some nodes are configured so you cannot connect with them if the repeater is
active. In this case you will receive the message "The node you
are calling is being used locally" If you receive this message
wait 5 or 10 minutes and then try again.
Should you stay connected to a node and there is no activity for 5 minutes, the
connection will time out and automatically disconnect providing voice IDs to
both nodes that the other node is disconnecting.
CONNECTING TO THE REFLECTOR
As above listen to your local machine and then announce your intention for the
Reflector before keying the Reflector Link ON command. When you hear the
confirmation ID always WAIT at least 15 seconds before transmitting as you are
most likely now connected with many repeaters and a QSO could be in progress.
If after 15 seconds you hear nothing, identify yourself and indicate you are
listening to the Reflector from "City
and, Prov./State, Country". With the world wide IRLP activity your local
repeater now has world wide coverage thus the suggestion to better detail your
QTH.
Don't be in a hurry to hear someone come back to you. You may have to do a bit of pleading from time-to-time to un-lodge someone from whatever they are currently doing.
Connections to the Reflectors DO NOT time out with no activity so it is not unusual for repeaters with minimal traffic to stay connected to the Reflector for extended periods of time.
If you are new to IRLP you should always consult with your local node sponsor to confirm the local guidelines on reflector connections in your area.
If you hear or wish to engage in a prolonged rag-chew (long discussion of a local nature) on your local repeater you may, out of courtesy to other node listeners, wish to drop the reflector.
ERROR MESSAGES
From time-to-time you may receive error messages when attempting to connect with
a node or reflector. The most common ones are:
"The
node you are calling is not responding, please try again later"
This is caused by a loss of internet connectivity to one end of the
call attempt.
"BEEP
Error- The call attempt has timed out, the connection has been lost"
This error occurs when a node is
OFF-LINE. Some nodes such as in the UK use dial-up connections and then,
only for short periods. Also there may be temporary net or node problems.
"The Connection Has Been Lost"
If the internet connection drops, this error message will be heard.
DO'S and DON'TS
In summary then a few do's and don'ts
· DO pause between transmissions to let others in or others to enter DTMF command.
· DO identify before sending DTMF command tones.
· DO hold your microphone PTT for about 1 second before talking to allow all systems time to rise.
· DO NOT rag-chew on your local repeater while connected to the reflector.
·
DO
pause for 10 seconds or when entering the reflector before talking.